Page 1 of 2
New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 8:19 am
by darknloud
Incoming calls to my Ooma number receive a scratchy man's voice saying "Sorry, but your call can not be completed."
Outgoing calls work fine.
Setup is "normal": Fios router to switch (not router) to Ooma.
Help? Thanks
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 8:55 am
by thunderbird
darknloud:
Reserve a static IP address in your Fios router for your Ooma device. Than place the Ooma device's static IP address in the Fios router's DMZ.
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 9:03 am
by darknloud
Thank you T-Bird. I'll try that. I did just see I can view the Telo over it's address, and it looks like I can give it a static address there so will try this.
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 10:07 am
by darknloud
OK - So I attempted to do as T-Bird suggested.
1) I added a static IP address to the router config of the Verizon FIOS router (192.168.1.100), and associated it with the MAC address of the Telo.
2) I added that static IP address to the DMZ Host on the Verizon FIOS router.
I have not altered configuration of the Telo, meaning I left its network config as "Automatic". I believe this is OK as the Router assigns it this static address.
Outgoing calls are fine, incoming calls still met with the "Sorry..." message.
Further thoughts ??
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 11:31 am
by darknloud
I've been in contact with Ooma customer support; they were able to place a call from another Telo device, but we've demonstrated doesn't work from other carriers.
So - they are elevating the service inquiry. I will post results here (and of course do welcome any further thoughts from this community).
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 12:10 pm
by thunderbird
darknloud:
You have eliminated the possibility that your router was blocking certain ports by placing the Ooma device in your router's DMZ. The problem is probably an Ooma Routing problem, but I listed some other things to check below:
Make sure that in My Ooma-Preferences-Blacklists- Community Blacklist and Personal Blacklist isn't enabled.
Make sure that in My Ooma-Preferences-Anonymous Call Block- isn't enabled.
If you still have the second Ooma line, try calling the second line with your cell phone.
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sat Mar 05, 2011 1:03 pm
by darknloud
Thank you T-Bird. Those didn't resolve the issue. Awaiting follow-up from Ooma.
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sun Mar 06, 2011 10:34 am
by jebersohl
Darknloud, I possibly have the same problem as you. Here is my problem: when SOME people call my Ooma number from the same area code, (555) say for anonymity, they can't just dial the 7 digit phone number (555-5555) as expected but have to dial the full 10 digit number (555-555-5555) in order for the call to come through. Some people can't even dial the full 10 digit number and get the "Sorry..." phone message. I have contacted Ooma about this on two separate occasions months apart and still no resolution. I don't understand how some numbers from the (555) area code can call with the 7 digit dialing with no problem while others have issues. I have had no other issues with Ooma, but this is a big one if people can't call my number as expected.
Darknloud, does this sound like your problem?
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sun Mar 06, 2011 10:55 am
by darknloud
jebersohl - I think we may have different problems, though perhaps both are due to Ooma network problems.
For me - this is a new installation and I've never gotten an inbound call (and have tried from cell numbers with different area codes). So I think where you have a peculiar issue with some - I seem to have a problem receiving calls from any one.
I'm hopeful I'll hear from Ooma Monday or Tuesday - and whenever I do I'll post our findings here.
Thank you for your interest.
Re: New Install-Outgoing calls OK; Incoming calls get "Sorry...
Posted: Sun Mar 06, 2011 11:59 am
by thunderbird
darknloud & jebersohl:
Some other suggestions:
Do both of you have a new phone number that were assigned by Ooma?
If the number is a new phone number and has no meaning to you, you could call Ooma Support and have them give you a different phone number.
Do you have anything plugged into your Ooma device's "Home" phone ports?
Try Inbound/Outbound calls with nothing connected to the Ooma device's Home port, and only a phone connected to the Ooma device's Phone port. With nothing connected to house phone system wiring.