Ooma Forums

New guy here. I installed my ooma last night as per instructions in the manual and I am not seeing the constant blue or red light that everyone here is talking about, plus I am not getting the Ooma dial tone. When power is hooked up, it flashes the lights in the beginning and then nothing.

I tried different configurations: 1. modem -> hub -> router, 2. modem -> router -> hub.

I can get to the internet just fine with both scenarios. I can also get to setup.ooma.com.

From setup.ooma.com, it says the following:
Intenet: Connected
Ooma Core: Connected
Phone Line: Disconnected
Phone Setup: Your phone line is configured for the ooma network
Second Line: Enabled
Voice Mail: Enabled

I signed up for the temporary number while porting, but have not done the process to port the number. I wanted to make sure I can make and receive calls first before doing so.

If anyone can help me, it would be great.

Note: I have done the hard reset (holding down the ooma tab for 30 secs) and also its been a couple of 5 hours since installation.

kenricko wrote:New guy here. I installed my ooma last night as per instructions in the manual and I am not seeing the constant blue or red light that everyone here is talking about, plus I am not getting the Ooma dial tone. When power is hooked up, it flashes the lights in the beginning and then nothing.

I tried different configurations: 1. modem -> hub -> router, 2. modem -> router -> hub.

I can get to the internet just fine with both scenarios. I can also get to setup.ooma.com.

From setup.ooma.com, it says the following:
Intenet: Connected
Ooma Core: Connected
Phone Line: Disconnected
Phone Setup: Your phone line is configured for the ooma network
Second Line: Enabled
Voice Mail: Enabled

I signed up for the temporary number while porting, but have not done the process to port the number. I wanted to make sure I can make and receive calls first before doing so.

If anyone can help me, it would be great.

Note: I have done the hard reset (holding down the ooma tab for 30 secs) and also its been a couple of 5 hours since installation.

Maybe this is why? Phone Line: Disconnected

Check the dimmer wheel on the right side to see how your Ooma tab is lit (red or blue).

How is your phone connected to your hub?

I set the dimmer switch to the lightest or even the other direction. The ooma tab still doesn't glow. When I press it, its red tho.

kenricko wrote:I set the dimmer switch to the lightest or even the other direction. The ooma tab still doesn't glow. When I press it, its red tho.

When you press the tab, do any of the other buttons light up?

Make sure you are turning the FADER control on the RIGHT side of the hub and not the volume on the left.

Also make sure you're plugging your phone into the PHONE port of the hub and not the WALL.

By the setup menu, everything should be working.

Did you register your ooma hub to be used WITH your landline? (integrated)? If so, you need your landline connected to the WALL port of the hub via a phone wire to the wall jack on your house. (I don't think you did this since you have a temp number from ooma, but I had to mention it)

Wayne

EDIT: Can you call your ooma number?

Groundhound wrote:

kenricko wrote:I set the dimmer switch to the lightest or even the other direction. The ooma tab still doesn't glow. When I press it, its red tho.

When you press the tab, do any of the other buttons light up?

Nope. Only if I hold it down, then it will cycle through the buttons.

Try the reset procedure here: http://www.ooma.com/forums/viewtopic.php?p=2599#p2599

Edit: Corrected for bad link.

Groundhound wrote:Try the reset procedure here: http://www.ooma.com/forums/viewtopic.php?p=30711#p30711

It says I am not authorized to see that forum. Am I missing something?

Hub factory reset sequence:

1) Remove the power for the Ooma device.
2) Hold down the Ooma tab [blue light] and connect the power. Hold for 30 seconds until all the lights start flashing.

Once the lights stop flashing, release the Ooma tab and the device will reset to factory settings.